Fibreglass Pool Ideas Eastern Bay of Plenty
In-ground fibreglass pools for Eastern Bay of Plenty, moulded and installed by the factory that makes them.
The factory that moulds every Bayside shell is in Whakatāne, and it runs its own installs across the Eastern Bay rather than handing them to someone else. For Eastern Bay of Plenty that means one company from the mould to the backfill. Below is what suits the section, what the range measures, and how the job runs from the first visit to the first swim.
At a glance
Sizes are quoted as internal, water-line measurements — an 8 x 4 is 8 x 4 of water. Depth is the shell height, and capacity is measured to the top of the shell.
Reading the picture
What to read off the photograph at the top of this page
The photograph on this page is one of ours and it carries no address — it is an idea, not a job in any of the towns named above. What is useful about it is the proportion: how much of a yard a pool of that size takes once the surround and the fence are in, and how the water line reads from the house. Measure your own clear space against that before you pick a model, because the pool is only part of what the section has to give up.
- The footprint, not the model Look at how much of the yard the water takes once the surround is in. That is the number that decides which model fits your section, and it is the one thing a plan drawing never shows as clearly as a photograph does. Measure your clear space, then choose the model.
- The water line A fibreglass shell is moulded in one piece, so the water line runs unbroken from end to end — no joins, no panels, nothing to line up. On a pool you look at that line every day of the summer, and it is the first thing that shows if the shell has been set badly.
- The surrounds, which finish it What sits around the pool is what makes a yard look deliberate rather than unfinished. Paving, decking and fencing are decisions to settle before the digger arrives, not after — and they are a separate purchase from the shell.
No install count appears on this page, and no claim about the ground at a named address. The factory covers this patch with its own crew and has done for long enough to know the country; how many pools are in any one of these towns is a question for the phone, not for a page.
The local picture
Fibreglass pools in Eastern Bay of Plenty
The Eastern Bay is the rest of the factory’s own patch: Edgecumbe, Matatā, Tāneatua, Murupara and the settlements between them. The first three are a short drive out from Whakatāne; Murupara is the long run at the southern end. Covering all of it directly, rather than handing it on, is the point. The factory keeps its own install crew for this patch, so a pool at Murupara and a pool in Whakatāne are run by the same people out of the same yard. Past the Eastern Bay the map changes hands: the wider Bay of Plenty, including Tauranga, Mount Maunganui and Rotorua, is the Tauranga yard’s, and the rest of the country belongs to the local installer for that region.
The ground and the access
The Eastern Bay is not one kind of section, and no page can tell you which kind you have. The factory page acknowledges the sloping sections, the coastal ground and the access, and says the team works those sites regularly. That is the reason to settle the site before the model is chosen: the pool that suits a flat section and the pool that suits a sloping one are rarely the same pool.
What the factory changes
Every shell in the country is made in Whakatāne, and the factory runs its own installs across this patch. There is no separate installer to brief, no second company to chase and no freight on a local job, and when something needs sorting it gets sorted at the source rather than through a middle layer.
What it looks like when it is finished
The shell is the same family of moulds in every town — what makes a pool local is the yard it goes into. Paving, decking, planting and the fence are a separate purchase and a separate decision, and they are what the pool is judged by once the water is in.
The factory is the installer
One company from the mould to the backfill
Most pool buyers never see the thing they are buying made, and most pool companies have never seen theirs made either — they buy a shell from a manufacturer and pass it on. In Whakatāne that layer is not there. Every Bayside shell is laid up by hand in five stages: gelcoat, corrosion barrier, structural laminate, core and rib, then the outer seal, with an inspection between each one. The same business runs the installs across the Eastern Bay, so the crew that sets your pool is the crew that has been in the factory all week.
A short haul
A local shell barely travels. That takes the risk out of the part of the job nobody sees: every trip on a truck is a chance for a shell to be damaged before it is even set, and the shorter the trip the less of that there is.
Built to a standard, inspected as it goes
Hand laid up in five stages with an inspection between each one, rather than built up and checked only at the end. Whatever is wrong shows up while the shell is still on the floor.
The warranty comes from the maker
The shell is moulded in our own factory, and it comes out of it with a twenty-year structural warranty and fifteen years on the finish. You deal with the people who made it.
What suits Eastern Bay of Plenty
Four things that decide the pool in Eastern Bay of Plenty
Most pools are chosen twice: once as an idea, and once against a tape measure. These four decide the second one.
Space on the section
Measure first. What fits is decided by clear space, not by the plan sketched on the back of an envelope, and every model in the range needs more room than its water-line dimensions suggest.
How you will use it
Decide who swims and how. Small children, teenagers, laps, or two adults at the end of the day — each of those points at a different model and a different depth.
Getting it in
Access is what decides most installs. A machine needs a run to the hole, or the shell comes over the house on a crane — worth knowing before the position is fixed rather than on the day.
Around the pool
Fencing is the part that is not optional and has to comply. Everything else around the water — paving, decking, planting — is a choice, and it is what the pool ends up looking like.
Plain English
In-ground pool, inground pool, fibreglass pool — the same purchase
People search all three. For a Bayside pool they describe the same thing.
In-ground pool
A pool set into the ground rather than standing above it. Every Bayside shell is designed to go in the ground, so an in-ground pool is the normal case rather than an upgrade. Where digging is not wanted there is a Freestanding option in the range — still a Bayside shell, sitting above ground.
Fibreglass pool
The pool body is a one-piece moulded shell, made in our Whakatāne factory and delivered complete. On site the work is preparing the base, placing and setting the shell, then everything around it — rather than building the pool body itself on site.
Swimming pool
The widest of the three and the one people type most. It covers a small plunge pool through to a 12 m family and lap pool — the difference being length, depth and how much of the section they take up.
A detail that catches people out: our sizes are internal, water-line dimensions. An 8 x 4 is 8 x 4. Depth is the shell height, and capacity is measured to the top of the shell. Whether you type inground pool or in-ground pool, it is the same pool.
What fits
What pool size works in Eastern Bay of Plenty
The range runs from the 3.6 x 2.2 m Tranquil plunge pool up to the 12 x 4.4 m Big Bertha, with the 4 x 2.4 m Pause, the 5.45 x 3.4 m Element, the 6.5 x 3 m Retreat, the 7 x 3.5 m Cove, the 8 x 4 m Satin, the 9 x 4.4 m Shoreline and the 10 x 4.4 m Coastline in between. All ten are laid up in Whakatāne and all ten can be seen there. Sizes are internal, water-line dimensions: an 8 x 4 is 8 x 4 of water, depth is the shell height, and capacity is to the top of the shell.
Start to finish
The sequence of a pool build in Eastern Bay of Plenty
People want a straight answer about what happens when. Here it is, in order.
- A look at the site — where the pool sits, how the machine and the shell get in, and where the equipment goes.
- A written quote — the pool in the ground and running, with the inclusions listed plainly.
- The shell is made — laid up by hand in five stages, inspected between each one.
- Dig and prepare — excavation, base preparation, and the hole looked at as it opens up.
- Set the shell — placed and levelled on the prepared base by the crew that quoted the job.
- Fill, commission and hand over — water in, equipment tested, water balanced, and the handbook handed across.
Expect the shell to go in quickly and the finish to take longer. Fencing in particular has to be done before the pool is used, not after, and it sits outside the pool price — ask for it to be shown on the quote.
Looking after it
What ownership looks like the year after
On handover day we go through the whole pool with you — the equipment, the water and the first week — so it all makes sense before we leave. After that it is ordinary care: chemistry in range and the gear looked after.
Nearby
Pool ideas for the rest of the factory’s patch
The factory covers Whakatāne and the Eastern Bay directly. These are the other areas with their own pages. If your town is not here, the wider Bay of Plenty — Tauranga, Mount Maunganui and Rotorua — is run by the Tauranga yard, and the rest of the country by the local installer for that region.
Questions
Eastern Bay of Plenty pool questions, answered
Which towns does the factory cover in the Eastern Bay?
The factory page names Edgecumbe, Matatā, Tāneatua and Murupara alongside Whakatāne, Ōhope and Kawerau. The first three are a short drive out from the factory and Murupara is the long run at the southern end. If you are further out than that, ask — the wider Bay of Plenty is the Tauranga yard’s patch and they will tell you straight.
Murupara is a long way out — is that a problem?
It is a planning question rather than a reason it cannot be done. It is a short haul next to the jobs this factory sends shells to at the other end of the country, and the crew that sets the pool is the crew that made it. What gets worked out at the site visit is the access and the ground, because that is what changes from section to section out here.
We are on a lifestyle block between towns — do you still cover us?
The Eastern Bay is covered directly by the factory, and that includes the country between the towns rather than just the town addresses. Send us the address and we will tell you which crew covers it — and if it belongs to the Tauranga yard instead, we will say so rather than leave you guessing.
Is a building consent required for a pool in Eastern Bay of Plenty?
Pool fencing is the part that is not optional: it has to comply with the building code and it is checked, whether or not the pool itself needed a consent. Depending on the section, a building or resource consent may also come into it, and that is worked through as part of the job rather than left to you. The fencing sits outside the pool price, so ask for it to be shown on the quote.
How long does a pool installation take?
Excavation and setting the shell are the quick part — days rather than weeks once the crew is on site. What takes the time is what comes after: filling, the surrounds, the fencing and balancing the water. You get a real sequence up front rather than just the fast part, so the garden and the fencing can be planned around it.
Which Bayside model should I look at first?
It follows the section rather than the town. Tight sections end up at the plunge and compact models — the Tranquil, the Pause and the Element. Sections with room usually take a 7 to 8 metre family pool, which is the Retreat, the Cove or the Satin. The full range with dimensions is on the pool range page if you want to see the sizes side by side before you ring anyone.
Who actually installs the pool?
The factory does. Whakatāne and the Eastern Bay of Plenty are run directly by the Bayside team, so the install crew is based ten minutes from where the shell was made rather than arriving from another region. The person who quotes your job is the person on your site when it goes in.
Are fibreglass pools in-ground pools?
Yes. A Bayside shell is designed to be set into the ground, so an in-ground pool is the normal case rather than a special order. The range also includes a Freestanding option where digging is not wanted; it is the same shell family, sitting above ground.
What is different about a fibreglass pool?
The shell arrives as one finished piece rather than being built up on site, so the on-site work is preparing the base, placing and setting it, and then everything around the water. That is also why the surface matters: ours is ChlorShield, the gelcoat system on every Bayside shell, and the ChlorShield page sets out what it is built to do.
What colours do fibreglass pools come in?
There is a full palette on the pool colours page, photographed on real pools rather than shown as swatches on a screen. You can also ask to see a colour in person before the shell is ordered — the light a pool sits in changes how a colour reads, and that is worth seeing for yourself.
Let us price a pool for your Eastern Bay of Plenty section
Send us where the pool is going and we will come back with the models and sizes that fit, a written price, and a time to walk the factory if you want one.